Faster Weld Inspection with Multi-group TFM

The TFM technique was introduced to ASME code in 2019, and the ISO standard is entering the final stage before publication. TFM is used today for various applications such as weld inspection, High Temperature Hydrogen Attack (HTHA), and Hydrogen Induced Cracking (HIC) detection. Eddyfi Technologies has tremendously invested to improve the technique on its various systems —Mantis™, Gekko®, and Panther™— with the ultimate goal of proposing a technique that’s compatible with the productivity and sensitivity expected by service companies and asset owners.

• Scanning speed has been improved several times through a fast Full Matrix Capture (FMC)/TFM mode and Plane Wave Imaging (PWI).
• Time Corrected Gain (TCG) has been implemented to ensure uniform amplitude with depth and position across TFM images.
• The experimental Amplitude Fidelity described in the ISO standard has been implemented to make sure that TFM images are properly discretized while avoiding oversampling them. With all the means in place to propose code compliant inspections, Capture™ software offers additional tools to perform weld inspection from both sides at a scanning speed of 100 millimeters (4 inches) per second.

Multi-group/Multi-modes

Capture software brings multi-group, i.e., several probes, and multi-mode capability together. It is possible to combine up to four groups/modes. Multi-group is particularly helpful when dealing with weld inspection as butt welds must be inspected from both sides. With an architecture up to 64x128, the Gekko portable Phased Array Ultrasonic Testing (PAUT) and TFM instrument can use two 64-element probes to perform TFM on both sides of the weld with large apertures providing optimum spatial resolution.

The following images show examples of multi-group (top) and multi-mode (bottom) configurations for a 25-millimeter (1-inch) V-weld plate containing three defects: toe crack, lack of sidewall fusion, and root crack.

The multi-group configuration shown has two groups using different 64-element probes each performing a PWI inspection with all the calibration tools described before (element check, wedge delay calibration, TCG, Amplitude Fidelity). The TFM uses the TT mode taking into account the first and second legs which allows the user to simultaneously see the TT and TTTT modes. This configuration allows the detection and characterization of all the defects.

The multi-mode configuration shows four modes, TT, TTT, TTTT and TLL, simultaneously using a fast FMC acquisition. The TT mode is calculated based on the first and second legs while the other modes are only calculated within one thickness of the plate. One can compare the detectability of the various defects using the various modes.

Both configurations are illustrated in the following video.

Productivity Improvements

Scanning speed when using TFM depends upon several factors.

• System architecture: A system needs to be able to record data on all channels simultaneously. Eddyfi Technologies developed the Gekko from the very beginning with an architecture that allows data recording on 64 elements simultaneously. Systems with a 32:128 architecture can only record the information on 32 channels simultaneously forcing them to fire all the elements twice to record a full 64-element TFM. This leads to a drop of the scanning speed by a factor of 2.
• Number of elements firing: The number of times a system needs to fire impacts directly the number of elementary signals that the system needs to process to calculate the TFM image. That’s why we implemented the PWI technique which allows a significant drop in element firing thus in elementary signals. Element firing also has an impact on Pulse Rate Frequency (PRF), and decreasing it allows for higher PRF.
• Number of pixels: A system is limited by its processing power; it can only calculate a given number of pixels per second. When doing multi-group or multi-mode configurations, the extra modes and groups essentially add more pixels to the system to calculate. You can see the importance of minimizing the number of pixels within each group/mode.

Capture software offers two more improvements for productivity. The first is the possibility to calculate the envelope of the TFM image. The envelope requires a reduced grid resolution to obtain the same amplitude fidelity using less pixels and thus improving productivity. For resolution less than 93 kpixels, the TFM calculation has been improved by 60%.

These capabilities are illustrated using the multi-group explained before. To inspect the 25-millimeter (1-inch) plate, we use a 50x52mm (1.97x2.08in) Region of Interest (ROI) area to make sure we inspect the full volume of the weld and the heat affected zone. The two images below show the scan plan performed for the inspection. A PWI configuration is used with a sectorial scan performed between 40 and 85 degrees with a step of 7 degrees. This means that we are only using 7 excitations instead of 64 for an FMC. Capture displays all the indications superimposed on the 3D view (element numbers, index offset, component thickness, etc.) and the angle between the refracted angle and the bevel. The latter is available for both PWI and PAUT. The values turn green when the angle between the refracted angle and the bevel is less than 6 degrees and orange if less than 8 degrees allowing inspectors to set their scan plan perfectly.

A 50x52mm (1.97x2.08in) ROI would require 202 kpixels to respect the Amplitude Fidelity as a pixel size of λ/6 is necessary. In the following image, you can see that by using the envelope the number of pixels drops to 77kpixels as λ/3.5 is sufficient to respect the Amplitude Fidelity. Dropping below 93 kpixels also unlocks the 60% speed increase.

A normal FMC acquisition (not fast mode) with 202 kpixels would lead to a scanning speed of 7 millimeters (0.3 inches) per second for a single group. Combining PWI with envelope and the 60% boost leads to a scanning speed of 207 millimeters (8 inches) per second. Going to a multi-group configuration, the final scanning speed is about 103 millimeters (4 inches) per second, which is on par or greater than most PAUT weld inspection while offering optimum spatial resolution across the ROI.

Data can still be exported in the 3D view of the component as shown in the following image with scan position indication. You can also see on the right of the C-scan that video smoothing has been added to make images look nicer - talk about picture perfect results.

Lower productivity was previously seen as a drawback of the TFM technique. Capture software provides multi-group and multi-mode capabilities at scanning speeds equal to or faster than PAUT inspections while providing optimum spatial resolution.

Did you know that Eddyfi Technologies offers application-specific PAUT packages to help take the guesswork out of what's needed for an effective and efficient inspection campaign? Check them out here.

Ready to raise the bar in your TFM inspections and stay Beyond Current? Contact us now discover Eddyfi Technologies solutions for better and faster assessments today!